BLADEZ ION 450 Manuel d'instructions

Please read all instructions before using this product.I n s t r u c t i o n M a n u a lDS160 Strobe

10SMART CHARGER 4067.1- It is safe to leave the charger connected to the battery pack when charging is completeor when charger power is off. To conser

11FLASH DIFFUSER 0591.3Flash DiffuserInstallation PostDiffuser Cut-outsDS160 StrobeDiffuser Retention TabLanyard HolesUSING THE DIFFUSERThe white diff

12TTLFull-2-1-3-4Ready LightFuelGauge321 TestO OnOnw/Lite160 DS160 ShroudBall-Type Mount“not included” with DS160Mount ScrewStrobe BaseIKELITE ARM SYS

13The female bulkhead connector permits different Ikelite sync cords, EV Manual Controller ora Fiber Optic Adapter to be connected to the strobe. Thes

14BulkheadConnectionRetaining RingStem O-ringBlue Band4103.51 Ikelite Sync CordSTROBE CONNECTION(illustration)DS160 Strobe Bulkhead Cap

15For use with the following types of systems:- Ikelite housings for digital cameras with external strobe connector but without TTL conversion circuit

16AIMING THE STROBEAIMING THE STROBEUse the modeling light to aim the strobe. Look thru the camera's viewfinder, and aim thestrobe so that the mo

17SWITCHES / FUEL GAUGETTLFull-2-1-3-4Ready LightFuelGauge321 TestO OnOnw/Lite160 Switch LockBatteryCompartmentThe DS160 features separate switches fo

18FUEL GAUGEWhen the switch is rotated to the “Batt w/Lite” position, the fuel gauge on the side of thestrobe will display 0, 1, 2, or 3 red LED light

19STROBE READY LIGHTTTLFull-2-1-3-4Ready LightFuelGauge321 TestO OnOnw/Lite160 Confidence LightReady LightSTROBE READY LIGHT AND TTL HOUSINGThe Ikelit

2TABLE OF CONTENTSIKELITE DS160 STROBE ...3Specifications ...3Introduction ...

20VISUAL INSPECTIONSVisual inspections are important. Take the time to examine the entire assembled setup(strobe, camera housing, arms, etc.) above wa

21Your Ikelite DS160 Strobe should be given the same care and attention as your otherphotographic equipment. After using your strobe in water, please

STROBE WILL NOT FIRE1. Make sure the battery pack is fully charged.2. Check the DS160 ready light. Turn the strobe’s mode switch to OFF an

23CUSTOMER SUPPORTCustomer support is available through an Authorized Ikelite Dealer or directly throughIkelite Customer Service. For a listing of dea

DS160 Strobe_4060.1-04-0115Please visit www.ikelite.com to register your Ikelite Digital Strobe within 15 days ofpurchase.Ikelite Underwater Systems50

DS160 SPECIFICATIONSCE - Compliant with applicable EU directivesComplies with FCC part 15, subpart B, Section 15.109 for Class “B” ProductsS p e c i f

INTRODUCTIONThank you for purchasing an Ikelite Strobe. Ikelite brings over 50 years of underwaterphotographic and lighting experience to the strobe m

5IKELITE DS160 STROBE (continued)DS160 STROBEThe Ikelite DS160 Strobe combines high intensity output and wide coverage anglein a compact, versatile de

OPENING THE STROBETurn the strobe OFF, and place the strobe face down on a flat surface.Slide the locking lever out by either grasping the sides of th

7OPEN RCD INDPLS IN U.S.A. UNLOCK INDPLS IN U.S.A. UNLOCK Pull Out Flip Up Rotate OPENING AND CLOSING (illustration)

8The 4060.1 DS160 Strobe includes a Lithium Ion (Li-ion) battery pack and smart charger.The battery pack requires Smart Charger 4067.1 (page 10).Li-io

9LI-ION BATTERY PACK 4067 (continued)CHARGING THE BATTERY PACKRequires Ikelite 4067.1 Smart Charger Li-ion. Do not attempt to charge the battery packw